Blackjack 55 Catamaran RTR with G26

You can buy a solid clutch from warehouse or bonzi , they both are the same. If you are running in salt water you should clean and lubricate your flex shaft after every session. Find More Posts by srt Dont know the speed but its a huge difference over stock, huge. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service.

All Listings

Shop by category

How did it handle, what is your strut height in relation to the bottom of the sponsons, strut angle if at all? Send a private message to black talon. Find More Posts by black talon. I bought 2 tanks instead of one and mounted them in each ponton as far down as possible and aprx. Look at youtube under wichspeed and dont look at my electrik cat that lookes like the large gas cat. Send a private message to soren wichmand.

Visit soren wichmand's homepage! Find More Posts by soren wichmand. Does ss enterprises have a website? I am looking for some engine mods for my BJ I was considering BH Hanson. I guess I will look at CC racing too Send a private message to philip clemmons. Find More Posts by philip clemmons. Send a private message to srt Find More Posts by srt Will someone post a photo of the throttle cable holder on the carburetor.

My cable came loose where it was glued and was wondering if anyone else has a better set-up? This time I used gorilla glue. Send a private message to MsDarla. Find More Posts by MsDarla. I have been running an octura x prop haven't gps it yet but friend of mine has same boat and same prop and had his gps He has since put an m5 kit in but hasn't gps yet. Wanted to know if anyone has tried an x or a x with this boat. We both have our boats trimmed up some and they still handle great.

We both love our boats and no problems with either one. Send a private message to hibby. Find More Posts by hibby. It is estimated and the only way to find out these things is to use a device that mesures the rpm. I have a nice 3 bladed 67 x 1,5 prop for my boat and it cavitates and is not usefull for my boat but other boaters find this prop super for their specific boat.

Then I have a 75 x 1,4 and that is the prop for my boat with std. I guess that the rpm on the enine is aprx. Best regards Soren Wichmand. Put a bonzi replacement clutch in and ran it this weekend and notice there is a play in the square reciever when the flex shaft is put in and the stock clutch it was a nice tight fit.

Twice when I brought the boat in after running it the flex shaft was bound in the receiver and I had to put a wrench on the square receiver and then a wrench on the back of the flex shaft to turn it to get the flex shaft out.

Doesn't seem to be effecting the performance on the boat when Im running it, its just a hassle. Black talon Im going to try a x prop and see how it does. Ineeded a 24v starter to start my BJ So I got 2 12v field box batt's and a toolbox and wired them up. I use my hobbico 90 starter to start my airplanes 60 size and also to start my 55" gas boat which had a pull start zenoah 26cc converted to a starting belt so i can use my starter for both.

Only quick short bursts on the 12v starter or you'll grenade the armature. That sucker spins good on 24v and doesn't even balk at starting that zenoah. And it's a good starting engine to boot. I upgraded the rudder to the aeromarine one single. Ditched the plastic fuel tank fora IV bag. That small vent hole was stinking up my house after running.

An Online Service Request is available at http: If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service.

When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. By submitting the item for service you are agreeing to payment of the service without notification.

Service estimates are available upon request. You must include this request with your item submitted for service. In addition you will be billed for return freight. Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

Electronics and engines requiring inspection or repair should be shipped to the following address: Horizon Service Center Fieldstone Road Champaign, Illinois All other Products requiring warranty inspection or repair should be shipped to the following address: Horizon Product Support Fieldstone Road Champaign, Illinois Please call or e-mail us at productsupport horizonhobby.

Electronics and engines requiring inspection or repair should be shipped to the following address:. Horizon Hobby — China Room , No. English French German Italian Spanish. Zenoah G26M 2-cycle engine with tuned pipe installed Weight: Fiberglass composite Prop Size: Extended engine mounting rails offer additional support and easy engine removal.

The carburetor comes pre-tuned with a new choke that makes starting easy. The clutch system allows you to start and tune the engine without the propeller engaging, for safer setup and operation.

Blackjack 55 Catamaran RTR with G26